Can you tell me were the Roadsmith service centers are in central Florida.
I live near the villages south of Ocala.
Thanks.
Goldwing:
A real butt kicking, wheel popping, tire burning old man's bike.
MIKE W.
Check their website
I believe there is one in Inverness at Trikes r Us. If not Trike Shop Daytona is a nice day ride for you. See Dan. He is top notch and a pleasure to talk with and a experienced and knowledgeable Roadsmith guy
Hope this helps
Jim
Jim
2015 Wing / Roadsmith:banana-cyclops:
:banana-cyclops:
Dawg is right - we have a dealer in Inverness. Great company called Trikes by Design - Larry will take care of you. Alternatively, The Trike Shop of Daytona can help also. Information below.....
Trikes by Design - Larry - 866-344-8637
The Trike Shop of Daytona - Anne or Dan - 888-396-8139
Let me know if need any more information or anything else I can help with!
Jim
Last edited by Hocky; 02-24-2017 at 09:22 PM. Reason: old age!
This is not a complaint, only a comment, I love my Road Smith. My problem a warped rotor, or rotors. I think it's the right rear, where the manual brake engages. Right now, it's in the the Trike Traders in Lake Afreld shop 'cause I did not want to make that long trip to Daytona with those logistical problems. The owner put his run out gauge on both rotors, couldn't find a problem, seems the rotor began to flex out of round as it warmed up on the ride and got worse as the ride continued, the feel was 'very pronounced'.
Since the owner could not locate the problem in the shop, he probably did the only thing he could, ordered two new rotors from Road Smith. At $90 a pop for rotors, shipping and labor, this is gonna be costly, but it is what it is. By the way, this owner is a good builder, been doing it for years, I have no reason to doubt his abilities.
Hocky - I checked with our lead trike installer, and he stated the easiest way to clean the tank (other than physically removing from chassis) is to drain the tank via the main transfer line. To do so, locate the transfer pump on the main trike frame. There is a fuel line coming out of the lower part of the auxiliary tank that you can follow up-stream to the pump. Clamp the line before the pump, remove line from pump, and remove clamp to drain the residual fuel into a suitable container. Depending on what you see coming out of the tank, may want to flush tank with fresh gas before reassembling the line.
If you have any questions about doing this, or help locating the pump, PLEASE call 800-331-0705 and ask for Mark. He is always happy to help.
Thanks!
Thanks much, good vote of confidence for Doug at Trike Traders, I'll pass it along. I think my problem is only with the rear right rotor, the hand brake rotor. Several months ago, I had it slightly engaged when I thought it was fully in the released mode, so I could smell it getting warm in a mile or so, I immediately knew the problem and fully released the hand brake, but probably not before there was some damage to the rotor metal. Oddly it took a while to get to the noticeable pulsating. I'm probably paying an extra $90 plus freight for the left rotor, but it's all good if it cures the problem. I thought a full post on this might shed some light on the problem...Again, thanks for the response.
I just converted my beloved 2010 Honda Goldwing into a Roadsmith.. I just took my first ride on a trike two days ago [3/6/17] my question is also that I don 't have an owner's manual either..
I found that I took to a trike like a fish in water (I didn't have a problem adjusting to it at all) and I've been two wheeling it for over 50 years..
I had it converted by the trike shop in Keene New Hampshire...
I do have a couple of questions, and would love to talk to someone with trike experience, it's easier to talk to a real person instead of texting....I'm totally glad I made the switch, and love the new ride..
Ronnie
Springfield, Massachusetts
WoW! Am I a happy boy here, I call the 800 # to Roadsmith and spoke with a gent named Jim, he was very, very helpful and answered my questions.. I have to admit after I hung up with him I had a smile on my face....I'm totally a newbe here and his answers totally relaxed my mind...
Thank you Jim
Ronnie from Springfield Massachusetts
Will do Jim, picking up it up this morning, I'll quiz him. I know this is gonna be financially painful, so if I'm doing something wrong, I want to know it and correct. I'm not hard on braking, so I'm not sure where I can improve. As I mentioned in a previous post, it's possible I left the manual hand brake engaged just a bit, could have heated the right rear rotor so there was some molecular change in the rotor metal cause heat transfer to the rotor causing a pulsating warp. just my opinion which ain't worth squat.
Jim, as promised, just got home and talking w/Doug, he could not specifically pin point the cause, and he's been in the business a very long time. He's seen many out of round rotors on cars and some on trikes, with no apparent cause, the fix is to replace. According to Doug, attempts to turn the rotor may be a losing proposition, if the rotor/rotors get warm again, then it may do the same thing.
He could not positively identify the out of round rotor, so both were replaced. He has the rotors, so if you'd like to have them, then he could do that. He has no idea that you could identify if the rotor/rotors were defective in manufacture, or whatever the cause, considering the cost of return, that might be a negative, but he has them if you want them.
He's convinced it was not a dragging brake, or some mechanical thing. He's not willing to ship them back at his cost which make sense. I touched checked the rotors after the ride home, they were warm and not hot to the touch, the pulsating problem is gone, nice smooth ride now. The OEM replaced rotors had 31,777 miles on them.
What I might do is disconnect the manual brake so there's no issue there, if there ever was one. One last thing, this fix cost me a whopping $420.94, so I'm taking every precaution I can so this does not happen again.
Ronnie,
That gent named Jim is the owner of Roadsmith, or actually one of the two, the other one being Doug. Jim is the guy answering all the questions here and knows his stuff and is a pleasure to talk to. I talked to Jim yesterday myself and was smiling too. Attaboy Jim!
SORE SHOULDERS?
Get The Right Cure
TriGlide Rake Solutions
Get Info HERE
Support YOUR Trike Talk Forum Community & Get Upgraded Features & Free Merch with a Gold Club Membership!
Click Here For Information
Visit Cut-N-Shoot Customs Website
Text or Call Papa: (346) 800-7946
Email: info@cutnshootcustoms.com[/B]
RS, I had the clear fender protectors put on when I got my 2012 conversion. Is there anywhere I can buy these protectors and put it on myself?
2012 Triglide Piaggio MP3 500 to get groceries 1991 FLHS as back up
"Better to have it and not need it than need it and not have it !"
Tiffany, Olive, Daisy, “The Three Musketeers” together again.
Thanks, but don't need a roll of that stuff and I'm awful with scissors, think I'll try for the precut if I can find it. I know Road Smith put it on precut, so it's out there, somewhere, hopefully they will monitor this and respond. I'll call them if they don't comment here, I thought someone else could use the information, that's why I posted on the Road Smith "We Can Help".
The smartest thing we’ve done, over all the years attending Daytona Bike Week, was revisit Roadsmith Trike in 2017. With age reminding us three wheels brings the fun back to cruising, we stopped in the shop, saw a 2005 Goldwing Trike, and a few days later, purchased it.
Anne, the Manager, and the crew walked us though the transition from 2 to 3 wheels. The honest answers to our questions made things happen. Anne had us out of the office quickly with a pink slip. She provided a shipping agent to deliver the Trike to a cycle dealer in Western NYS. The Trike was delivered in a brief time. Roadsmith Trike forwarded the previous owner’s accessories, manuals and parts in the trunk.
The service agent at Arkport Cycle, a man that has serviced several cycles purchased in Arkport, did a NYS Inspection, and Serviced the Trike. He was impressed with the Trike and found no issues of concern. If you’re thinking of shifting to a Trike, and are in Daytona, it would be worth your effort to stop at Roadsmith Trike of Daytona Beach! Check their http://www.roadsmithtrikes.com/daytona/ postings.