I cannot get the picture I have on my phone to post in the reply.
Printable View
I cannot get the picture I have on my phone to post in the reply.
[QUOTE=Longbeard71;727130]I cannot get the picture I have on my phone to post in the reply.[/QUOTE]
I can't make pictures upload from my phone either .. don't feel bad ... in my case ... I think it's operator error ... :D
Maybe the same here Fuzzy. :D
[QUOTE=Longbeard71;727130]I cannot get the picture I have on my phone to post in the reply.[/QUOTE]
Post some pics on here from your home computer then, most can't from a phone and some can
All for now Trampas
[ATTACH=CONFIG]82203[/ATTACH][ATTACH=CONFIG]82204[/ATTACH][ATTACH=CONFIG]82205[/ATTACH]
I took my iPad out to the shop and got some pics I could post.
[QUOTE=Longbeard71;727722][ATTACH=CONFIG]82203[/ATTACH][ATTACH=CONFIG]82204[/ATTACH][ATTACH=CONFIG]82205[/ATTACH]
I took my iPad out to the shop and got some pics I could post.[/QUOTE]
so im guessing you used square tubing but noticed you don't have a park brake pedal
[B]Longbeard71, do you have any pictures of the main part of the support and how it is attached to the frame? Is it just one piece of 1 inch square tubing?[/B]
[QUOTE=MDF48;727842][B]Longbeard71, do you have any pictures of the main part of the support and how it is attached to the frame? Is it just one piece of 1 inch square tubing?[/B][/QUOTE]
What he said. lol need to see how mounted. Thanks
I milled slotted holes in the square and used stainless steel ubolts around frame. I put some gussets in at the 90 degree turn for strength. Mine is a 2011 so no brake pedal but there is room to move the mount toward the back more. You would need to measure to see if it would clear. I have made two of these one for my 2011 and a 2012 works good for me they could be made taller mine is level with front floorboard. It makes it very easy to get on and off.
[QUOTE=Longbeard71;727869]I milled slotted holes in the square and used stainless steel ubolts around frame. I put some gussets in at the 90 degree turn for strength. Mine is a 2011 so no brake pedal but there is room to move the mount toward the back more. You would need to measure to see if it would clear. I have made two of these one for my 2011 and a 2012 works good for me they could be made taller mine is level with front floorboard. It makes it very easy to get on and off.[/QUOTE]
OK, one more request. If you don't mind could you jack it up, take the entire unit off and take some pictures? :D:clapping:
Well just messing with you, but did you take any pictures of it after you made it but before you mounted it? Thanks.
Sorry I do not have any pics before I installed it. It is a single piece of 1" square tubing across the bottom.
Clay, you don’t have to take it off, but just jack it up and crawl under and take some pictures, lol, just kidding.
[ATTACH=CONFIG]82266[/ATTACH]
Maybe this will help, from trike mid step web site
[ATTACH=CONFIG]82268[/ATTACH][ATTACH=CONFIG]82269[/ATTACH][ATTACH=CONFIG]82270[/ATTACH][ATTACH=CONFIG]82271[/ATTACH]
Here are a few pictures of a mid-step that I made. It is made from 1" X .125 wall square tubing. Had no way to bend it, so I made two 45* angles. Floor boards are patterned after a set of Cobra Floor boards made for a Kawasaki VN800 They are cut down 2" made from 1/2" aluminum. Pardon the pictures of being upside down. They are not like that on my computer.