[ATTACH=CONFIG]87684[/ATTACH]
[ATTACH=CONFIG]87685[/ATTACH]
[ATTACH=CONFIG]87686[/ATTACH]
I'll bet with a little engineering, your wife could use the pipes for more luggage storage ... :D
Printable View
[ATTACH=CONFIG]87684[/ATTACH]
[ATTACH=CONFIG]87685[/ATTACH]
[ATTACH=CONFIG]87686[/ATTACH]
I'll bet with a little engineering, your wife could use the pipes for more luggage storage ... :D
[QUOTE=JaysGone;707936]If I was 20 years younger I might have strength to try a build.
I did about 7 years ago bring a total POS Valkyrie back form the dead. Rebuilt it to 98% OEM with NOS parts.
Cost me a small fortune took a little less then a year to do. Couldn't get anyone to build me a metric trike. Again sold it for a big loss.
Today I cant work on anything for more then 30 minutes. Its all I have in me. So seeing what your doing is a pleasure.
I hope the build goes well for you and your wife enjoys the ride.[/QUOTE]
we can build a trike out of most anything
With everything going on, it's been some time posting. What is that independent rear end from? That's much more engineering than I've done or even want to do. I really do like that setup.
We took the bikes on a trip to Eureka Springs Arkansas. Mechanically both bikes did great! The RoadStar had one minor issue that I took care of in a few minutes. The Stratoliner body was being held on by bungee cords by the time we got home. Louisiana roads, especially around Lafayette, are horrendous! That area is so bad we had to pull off the highway a few times to give my back a break and tighten the bungee cords.
Anyway, once we recovered from the ride, I got to work on the RoadStar for painting. Tore it down, went through the mechanics, adjusted a few things, and began priming and sanding. Coated the underside with flex seal white and then began painting the top side with gloss white Rust-Oleum oil base paint. Shot two wet coats over two days and it shines! Going to be shooting KBS Diamond Clear with some pearl additive in the next few days.
The high temps might put that on hold for a while though. Maximum recommended temperature is 80 degrees and it's been hitting 106 under the carport. Pretty sure my wife won't let me paint in the house.But here are a few pictures of her pretty gloss white parts.
[ATTACH=CONFIG]89727[/ATTACH][ATTACH=CONFIG]89728[/ATTACH][ATTACH=CONFIG]89729[/ATTACH][ATTACH=CONFIG]89730[/ATTACH]
[QUOTE=Rickus Dickus;768734]With everything going on, it's been some time posting. What is that independent rear end from? That's much more engineering than I've done or even want to do. I really do like that setup.[/QUOTE]
diff is ford. suspension is subaru.. i made the cross member
[QUOTE=stacebg;769028]diff is ford. suspension is subaru.. i made the cross member[/QUOTE]
My having a solid rear axle does have its drawbacks in ride smoothness. I thought about a rear axle as you have installed, but being belt drive makes things much harder to do one.
Fabricated some forms and using epoxy resin, fiberglass cloth with mat, I now have some fender skirts. Just finished fitting them to the RoadStar. Cut out the area for the forks to pass, pressed a piece of PVC pipe to the forks, and laminated three layers of six ounce fiberglass cloth. Tomorrow I will see what the look like. As I type, I realize I'll either have to finish them on the bike or make the fork covers removable as they will not pass over the fender mounts. Oops!
[ATTACH=CONFIG]89946[/ATTACH][ATTACH=CONFIG]89947[/ATTACH]
Finished the fender skirts and began painting. Had to repaint the front fender as I messed it up fiber-glassing the fender skirts to fit it. One more good wet coat of white, let dry several days, and then mix some pearl with clear and clear coat everything... And NO, that is not a wheel and tire. It's my barrel fan!!!
[ATTACH=CONFIG]90230[/ATTACH][ATTACH=CONFIG]90231[/ATTACH]
[QUOTE=FuzzyWuzHe;756225][ATTACH=CONFIG]87684[/ATTACH]
[ATTACH=CONFIG]87685[/ATTACH]
[ATTACH=CONFIG]87686[/ATTACH]
I'll bet with a little engineering, your wife could use the pipes for more luggage storage ... :D[/QUOTE]
My wife for sure will. Trike's looking great!
I think you gotta come to the Maggie Valley in Sept to show us your handi work. I can just imagine the talk at the evening rocking chair conferences in front of the rooms.:cool: