What did you do to Your Tri-Glide Today?

[hardwickbv]

Installed the Comfort Lift at full height and Adjustable passenger pegs after work today.

Then took it for a 25 mile cruise to check it out.

Relocating the Tour-Pak tomorrow.

Oil cooler and filter relocation will have to wait till next weekend so I can put another 900 miles on then I will be at the 5000 mark.

Bob

[hardwickbv]

Moved Tour-Pak back 2" then took it for a 35 mile trip to see how she likes it. Got a thumbs up.

Thanks to DK for all the great products.

2 more to install next weekend.

Bob

[DK Custom Products]

Received my tour pack relocation kit and Stealth LED driving lights. Got the tour pack done and the lights mounted. Finish up the wiring tomorrow as soon as I can find a good place to tap into the existing harness. Mounted mine below the floor boards. Thanks Kevin for more great products!

I ran mine under the floorboards for awhile...it is a stealth location and looks really cool.

Appreciate your business.

Kevin

[DK Custom Products]

Moved Tour-Pak back 2" then took it for a 35 mile trip to see how she likes it. Got a thumbs up.

Thanks to DK for all the great products.

2 more to install next weekend.

Bob

Cool! Thank you, we appreciate it, and I believe you will be very pleased with your upgrades.

Kevin

[Recall]

I ran mine under the floorboards for awhile...it is a stealth location and looks really cool.

Appreciate your business.

Kevin

Finished the install. Soldiered the wire extensions in. Used di-electric grease and heat shrink tubing to seal everything up and keep out corrosion. The tubing on the wire extensions was big enough with a little help to go over the tubing on the wires coming out of the lights. Made for a slick, clean, and waterproof install. I have to say those posi-tap connectors are the cat's meow. Slick set-up!

Thanks again Kevin, for a well put together and thought out package.

[DK Custom Products]

Finished the install. Soldiered the wire extensions in. Used di-electric grease and heat shrink tubing to seal everything up and keep out corrosion. The tubing on the wire extensions was big enough with a little help to go over the tubing on the wires coming out of the lights. Made for a slick, clean, and waterproof install. I have to say those posi-tap connectors are the cat's meow. Slick set-up!

Thanks again Kevin, for a well put together and thought out package.

We've been very impressed with the posi-taps too.

Thank you!

Kevin

[rhino 2]

Put the DK floorboard [rider] extensions on the new 17..

[Fearless]

Put the DK floorboard [rider] extensions on the new 17..

You wouldn't think that small distance would make such a huge difference but.. it sure does. Cool legs happy legs. Fred

[rhino 2]

You wouldn't think that small distance would make such a huge difference but.. it sure does. Cool legs happy legs. Fred

Not only that my thighs aren't hugging the gas tank, Like with my 11, after a while my jeans rubbing against the tank wore the paint off...

[uncledoc]

Installed floorboard extensions

Installed FL-Vied-10 after removing the cat . . .(not sure if I need to adjust the settings or not)

Cool wings and tank lift next week . . . failed to remove them before trading in the FW . . .

Uncledoc

[427dave]

Had the new 120 ST engine dyno'ed and tuned. It was running rich so I hope now the gas mileage will increase. Runs a lot better and smoother. Final readings Max Power = 116 Max Torque = 130. It runs a lot better than the old 103

Going to make a run with the wife this weekend

[graygoat]

Installed floorboard extensions

Installed FL-Vied-10 after removing the cat . . .(not sure if I need to adjust the settings or not)

Cool wings and tank lift next week . . . failed to remove them before trading in the FW . . .

Uncledoc

On the vieds, I called nightryder and they said 75%. most post I found said 50 to 65%. Set mine at 65% and bike runs nice, so I left it there. Good luck.

[DK Custom Products]

Installed floorboard extensions

Installed FL-Vied-10 after removing the cat . . .(not sure if I need to adjust the settings or not)

Cool wings and tank lift next week . . . failed to remove them before trading in the FW . . .

Uncledoc

On the vieds, I called nightryder and they said 75%. most post I found said 50 to 65%. Set mine at 65% and bike runs nice, so I left it there. Good luck.

What graygoat said.

I've found that every bike runs a bit differently. So I start at 50% and move up and down, riding about 25 miles or so at each setting. You will know which setting is best after testing out some different ones above and below 50.

Kevin

[uncledoc]

Thanks Greygoat and Kevin . . . will try the 75% setting first.

[hardwickbv]

Installed the filter relocation kit and EBS with catch can today.

Tried to install the Oil cooler and found that no matter what I tried it would not fit with my Coolmaster fans on.

Finally gave up and finished the filter relocation without it.

Looks like I will need to return it.

Bob

[Grumpy7760]

What didn't I do lol changed handle bars and grips , moved tour pack back ,raised tank , extended floor boards , put on mirror extenders , extended shift peg , have new seat and wind shield coming soon

And that was all this past week

[headheaded]

Thanks Greygoat and Kevin . . . will try the 75% setting first.

i tried setting all over the place and seddled on 25%. it runs good. no cat and free flowing mufflers.

[DK Custom Products]

Installed the filter relocation kit and EBS with catch can today.

Tried to install the Oil cooler and found that no matter what I tried it would not fit with my Coolmaster fans on.

Finally gave up and finished the filter relocation without it.

Looks like I will need to return it.

Bob

Yeah, no way to have an oil cooler with the Cool Masters. The oil cooler will fit with the Mighty Mites.

Kevin

[DK Custom Products]

What didn't I do lol changed handle bars and grips , moved tour pack back ,raised tank , extended floor boards , put on mirror extenders , extended shift peg , have new seat and wind shield coming soon

And that was all this past week

You've been busy! Lots of little things that will make for a much more comfortable ride!

Kevin

[Recall]

Yeah, no way to have an oil cooler with the Cool Masters. The oil cooler will fit with the Mighty Mites.

Kevin

Good to hear. Never thought about clearance issues. I will be ordering my oil cooler and filter relocation kit before too long.