Csc hitch

[redneckray]

Does anyone know of where i can purchase the flat bar that goes in the champion hitch, or even if i had the measurements on one, got a project that i want to play with to help others on here that own a champion kit,
i called champion dealer near me and they want $160.00 for it, lol, i just want one, not a whole box of them,
ray

[redneckray]

I want to thank everyone for there help with this, guess i will have to look elsewhere for help.
Ray

[skip20]

How bout a picture so we can see what the heck your asking about!

[ricle41]

If you are looking for the drawbar that goes into the receiver hitch, any Walmart will have them in their camping, RVer section.

Hope that helps.

[skip20]

"the flat bar that goes in the champion hitch"

As far as I know, it's a 1.25" X 1.25" square bar ot tubing.
Don't know of any flat bar that will fit in there.

[FBTRIKE]

Skip20 is correct, square tubing goes into reciever with a piece of flat bar welded to it for the ball to mount on.

[redneckray]

Thanks,
i was told it was a flat bar that went in the rear, thanks again,
i don't have a pic of it,

[Gorilla]

Ray do you care if the champion is on a Honda or a Harley. I will try and get some pictures for you later (Wednesday) with sizes.

[redneckray]

There is a member here[salty] and has one that he sent me a pic of his and it is a flat bar, he wants to use the carrier i have, but need to make a receiver for him to use it on his trike,

thanks for your help

[ricle41]

The title of your thread says CsC trike kit, and you ask about a champion kit. I have a CSC in my driveway, and I looked at the parts list for a champion conversion on a couple of different bikes, and they all take the
1 1/4" square tubing.

Don't know what your situation is, but any trailer supply dealer or walmart carries the drawbar to fit them.

[redneckray]

Thanks for your input

[Nauga Mok]

I think what Ray's looking for is not the hitch itself, but the reciever assembly it plugs into. Ray, have a look at the Champion instilation instructions on their web site. Section 6 of their instructions has the optional hitch reciever instilation instructions & a diagram of what it looks like. It's basicaly just a couple of pieces of square tube & a couple of pieces of flat bar which bolts onto the muffler hanger supports. I looked at the '08 & down HD kit's instructions, but I'd think they're all the same in that area. Ray, one of the reasons for the $160 price tag is it includes the trailer plug & wiring. Even so, they seem to be pretty proud of a few bits of metal welded together & a little wire.

NM

[redneckray]

Nm,
thanks for your input, i'll go see if i can see what you are talking about,
thanks again
ray

[BlueTrinity]

Ray,

Here's what you're looking for. It's a 2.5" x 0.5" x 20" bar of steel.

At 11.5" it takes a 4" bend to form a 2" rise.

Hope that helps.

[redneckray]

Thanks, that looks like it, did they put those on some of the trikes and not all of them?

[BlueTrinity]

Can't honestly answer that Ray.

I will point out that this a CSC (California Side Car) hitchbar and not a Champion which most of the responses are refering to. You titled the post for a CSC hitch, but you referred to it as a Champion. I think that's where the coonfusion is coming from.

You can't see them well in the photo, but there is a loop welded to the bottom that carries the hitch pin and there's also a threaded hole for a bolt that screws tight against the cycle bracket to eliminate any vibration.

Good luck.

[redneckray]

Lolllllllll a mistake on my part, i didn't know what the csc meant, i was thinking it was champion, i thought they were all the same, grinn, but you sure have helped me out with it all, thanks again and all others too,
i only know vw'sm but guess i need to learn about it all,

[1800 06 Champion Trike]

My Champion has the square stock insert with a piece of flat stock where the ball is attached.
This is the factory one that came with the kit.

[Saltywheels]

Gee Ray, I thought I sent you all the pics & measurements you needed And, yeah dude, as I mentioned...it's a Cal SideCar & NOT a Champion. rgds.

[ricle41]

I can see why we are all confused. I own an '04 CSC conversion on a GL1500A, and the drawbar in that last pic is completely different than mine.
Mine uses the 1 1/4" square bar that slides into the receiver.