Local dealer custom Freewheeler

[Gone2Three]

The front rim is from RC Components, it is new for 2017.

http://shoprccomponents.com/clutch-chrome/

Thanks Val.. Your the best!

[trike lady]

Thanks Val.. Your the best!

You're welcome.

[haute pursuit]

Those rear tires have way too much height. The one I am building is 25" tire height on 18" rims. The tires on the bike posted are easily 27" height. Aspect ratio is probably 50 to 55 as opposed to the 35 I'm using. If it did have fenders they would tower over the trunk and ruin the lines.

[Gone2Three]

Those rear tires have way too much height. The one I am building is 25" tire height on 18" rims. The tires on the bike posted are easily 27" height. Aspect ratio is probably 50 to 55 as opposed to the 35 I'm using. If it did have fenders they would tower over the trunk and ruin the lines.

[BillR]

The Tri hits me best.

What, no Road Glide?

Here they are, three different versions. They don't give you much to use at the site.

Here is what I did with my '07. Had a chopped tour pack set up for the solo seat, not in the pic.

[trike lady]

Now that's nice looking.

This was a show bike I was working on, this is an early pic. The two added pics will give you an idea of what I was going for.

[onebadeagle]

Not Impressed

[Gone2Three]

Stopped in at dealer during lunch to check on progress of my lower fairing install.

While looking around i noticed that they have fabricated the rear fenders on that custom trike from previous visit ...

[paws]

[QUOTE=Gone2Three;504728]Stopped in at dealer during lunch to check on progress of my lower fairing install. They have fabricated the rear fenders on the custom trike now...[QUOTE]

Are we going to see the completed project at Kerrville????

[Gone2Three]

[QUOTE=paws;504730]

Stopped in at dealer during lunch to check on progress of my lower fairing install. They have fabricated the rear fenders on the custom trike now...

Are we going to see the completed project at Kerrville????

Hey Carla nahhh...this is a one off that they've been working on a for about a month. I think it's a customer's money pit

[peteg59]

^...Not "knockin'" anyone's fab ideas, but those fenders look like something sitting on the shelf over at my local Tractor Supply!!!

In that vein, simple is 99.9% better most days...

Hopefully once it's painted to match, it'll be a true eye~catcher!

If you can, please keep us posted on how it gets "finished", Randall.

[Gone2Three]

^...Not "knockin'" anyone's fab ideas, but those fenders look like something sitting on the shelf over at my local Tractor Supply!!!

In that vein, simple is 99.9% better most days...

Hopefully once it's painted to match, it'll be a true eye~catcher!

I agree with that, the metal was a thicker gauge than normal and minimal at that. At least it doesn't have the bare tires anymore we'll see

[HDB0B]

Can you get any info on the adapters they used to go from 4 lugs to 5 lugs? This pushed the tires out a bit and required the new fenders ... I suspect???

Bob

[trike lady]

Looks very amateur, does look like they adapted trailer fenders to the trike. Better looking fenders here for trikes: http://www.oldinc.com/fenders/cutyou...nderblank.html

Adapters: http://www.performancewheeladapters.com/4-lug-to-5-lug/ https://coyoteaccessories.com/wheel-...wheel-adapters

[Gone2Three]

I'll have to check on what adapters were used next time I'm back Bob, my regular service guy wasn't there today and it was super busy with their year end closeout.

[haute pursuit]

Can you get any info on the adapters they used to go from 4 lugs to 5 lugs? This pushed the tires out a bit and required the new fenders ... I suspect???

Bob

I ordered mine from Amazon.

[haute pursuit]

Can you get any info on the adapters they used to go from 4 lugs to 5 lugs? This pushed the tires out a bit and required the new fenders ... I suspect???

Bob

Its the diameter and width of the wheel/tires that required the new fenders. You can offset the additional space required for the adapters with backspacing/offset on the new wheels. It took me awhile to find the right combo after I bought the adapters. I saved a ton of money over buying custom forged 4 on 4.25 wheels though. Like $2K difference...

[haute pursuit]

Here are a couple of pictures of the work so far on my Free. Still waiting on the custom rear fender brackets to be fabricated, the front fender, V&H dresser duals, and a bunch of other little stuff. It has been a long process, but getting close to the end finally.

[Cainam]

Here are a couple of pictures of the work so far on my Free. Still waiting on the custom rear fender brackets to be fabricated, the front fender, V&H dresser duals, and a bunch of other little stuff. It has been a long process, but getting close to the end finally.

That is Sweet!!! Can't wait to see completed pics!!! Great job!!!

[Gone2Three]

Its looking good there Blake