150 Most Recent Posts

Thread AuthorPostersPost AuthorForumThread/Post Link
skisnow8061skisnow806Champion Trike2002 goldwing w champion conversion...
Voo Doo Blue3trike ladyNew Member Introduct...New Pacific North Wet member
Oldman-TriGlide4jmhenrieHarley Tri GlideOpen or Closed Trailer for 2028 Tri...
Voo Doo Blue3rhino 2New Member Introduct...New Pacific North Wet member
Voo Doo Blue3Voo Doo BlueNew Member Introduct...New Pacific North Wet member
Mykneesbehurtin10rhino 2Harley Tri GlideTri Glide Reverse Motor
Geep20207trike ladyNew Member Introduct...New Member
Aging Gracefully5NotgrownupHarley Freewheeler /...switching Tri-Glide for Road Glide ...
Grandpot5GrandpotHonda TrikesFront tire?
Geep20207Marc HNew Member Introduct...New Member
Mykneesbehurtin1019jmanHarley Tri GlideTri Glide Reverse Motor
Geep20207Uncle FesterNew Member Introduct...New Member
Geep20207ZammyNew Member Introduct...New Member
Geep20207rhino 2New Member Introduct...New Member
Aging Gracefully5seniorsgtHarley Freewheeler /...switching Tri-Glide for Road Glide ...
Grandpot5NotgrownupHonda TrikesFront tire?
Grandpot53W-loneriderHonda TrikesFront tire?
Geep20207woodyNew Member Introduct...New Member
Trampas3PanheadSteveHarley Tri GlideWas at my dealer today
Trampas3SeaweedHarley Tri GlideWas at my dealer today
Grandpot5cycle7447Honda TrikesFront tire?
Grandpot5tourmanHonda TrikesFront tire?
ultrafxr5TrampasHarley Tri GlideFinished at last . . . well at leas...
Trampas3TrampasHarley Tri GlideWas at my dealer today
Grandpot5GrandpotHonda TrikesFront tire?
Geep20207Geep2020New Member Introduct...New Member
Oldman-TriGlide4NotgrownupHarley Tri GlideOpen or Closed Trailer for 2028 Tri...
Oldman-TriGlide4ultrafxrHarley Tri GlideOpen or Closed Trailer for 2028 Tri...
Noodles1073BrokenBackJackHarley Freewheeler /...Very Nice Gloves
Oldman-TriGlide4Oldman-TriGlideHarley Tri GlideOpen or Closed Trailer for 2028 Tri...
RedOregon13Papa ZookHarley Tri GlideUpgrades on '24 Triglide?
Bama boy4DragonStallion TrikesStallion fuel pump
Bama boy4DragonStallion TrikesStallion fuel pump
Bama boy4DragonStallion TrikesStallion fuel pump
Papa Zook239SullyNew Member Introduct...What Made You Join TrikeTalk Forum?
RedOregon13RedOregonHarley Tri GlideUpgrades on '24 Triglide?
RedOregon13NotgrownupHarley Tri GlideUpgrades on '24 Triglide?
phillipschuckann7NotgrownupHonda TrikesWho made my trike?
Papa Zook239ol' schoolNew Member Introduct...What Made You Join TrikeTalk Forum?
PKLGW2pawsHonda Trikes2007 gl1800 motor trike
ultrafxr5Papa ZookHarley Tri GlideFinished at last . . . well at leas...
Noodles1073NotgrownupHarley Freewheeler /...Very Nice Gloves
ultrafxr5NotgrownupHarley Tri GlideFinished at last . . . well at leas...
Papa Zook239rhino 2New Member Introduct...What Made You Join TrikeTalk Forum?
PKLGW2PKLGWHonda Trikes2007 gl1800 motor trike
Papa Zook239skisnow806New Member Introduct...What Made You Join TrikeTalk Forum?
Speedy Pete12JTJerseyNew Member Introduct...New member from Alberta, Canada
Just BOB2Just BOBStallion Trikesinfo
ultrafxr5Longbeard71Harley Tri GlideFinished at last . . . well at leas...
ultrafxr5ultrafxrHarley Tri GlideFinished at last . . . well at leas...
ultrafxr5TrampasHarley Tri GlideFinished at last . . . well at leas...
ultrafxr5ultrafxrHarley Tri GlideFinished at last . . . well at leas...
Noodles1073Noodles107Harley Freewheeler /...Very Nice Gloves
Speedy Pete12cycle7447New Member Introduct...New member from Alberta, Canada
RISal24!12cycle7447New Member Introduct...New member..new to trikes
phillipschuckann7Papa ZookHonda TrikesWho made my trike?
RISal24!12ol' schoolNew Member Introduct...New member..new to trikes
Bama boy4Grey_Ghost_27Stallion TrikesStallion fuel pump
phillipschuckann7trike ladyHonda TrikesWho made my trike?
RISal24!12trike ladyNew Member Introduct...New member..new to trikes
Speedy Pete12RustyBNew Member Introduct...New member from Alberta, Canada
RISal24!12Marc HNew Member Introduct...New member..new to trikes
Bowie11RustyBNew Member Introduct...New to trike, old time rider
RISal24!12RustyBNew Member Introduct...New member..new to trikes
RISal24!12rhino 2New Member Introduct...New member..new to trikes
RISal24!12hardwickbvNew Member Introduct...New member..new to trikes
Bowie11hardwickbvNew Member Introduct...New to trike, old time rider
RISal24!12Uncle FesterNew Member Introduct...New member..new to trikes
Bowie11ZammyNew Member Introduct...New to trike, old time rider
RISal24!12SullyNew Member Introduct...New member..new to trikes
RISal24!12ZammyNew Member Introduct...New member..new to trikes
Chief80138520fdHarley Tri GlideHow many miles on your Triglide?
RISal24!12GorillaNew Member Introduct...New member..new to trikes
RISal24!12RISal24!New Member Introduct...New member..new to trikes
woody19woodyHonda Trikes2019 Goldwing CSC
DK Custom Products362NotgrownupHarley Tri GlideWhat did you do to Your Tri-Glide T...
Bouncer10NotgrownupHarley Tri GlideDrive Belt Replacement Time
Bouncer10BouncerHarley Tri GlideDrive Belt Replacement Time
Bouncer10BouncerHarley Tri GlideDrive Belt Replacement Time
phillipschuckann7GorillaHonda TrikesWho made my trike?
rjd637brianlHonda Trikes1989 Honda Goldwing trike opinions
DeathBySnuSnu19GorillaVW Powered TrikesVolkswagen Kit Cars
DK Custom Products362520fdHarley Tri GlideWhat did you do to Your Tri-Glide T...
SHARKDIVER4DK Custom ProductsGeneral Harley Chatsuper shox
phillipschuckann7trike ladyHonda TrikesWho made my trike?
phillipschuckann7ol' schoolHonda TrikesWho made my trike?
phillipschuckann7rhino 2Honda TrikesWho made my trike?
phillipschuckann7phillipschuckannHonda TrikesWho made my trike?
Bowie11Uncle FesterNew Member Introduct...New to trike, old time rider
RedOregon13RedOregonHarley Tri GlideUpgrades on '24 Triglide?
DeathBySnuSnu19DeathBySnuSnuVW Powered TrikesVolkswagen Kit Cars
Bowie11woodyNew Member Introduct...New to trike, old time rider
Just BOB2GorillaStallion Trikesinfo
SHARKDIVER4WindyOneGeneral Harley Chatsuper shox
Bouncer10GorillaHarley Tri GlideDrive Belt Replacement Time
Just BOB2Just BOBStallion Trikesinfo
Chief80138CagmoHarley Tri GlideHow many miles on your Triglide?
PopPop13consitterNew Member Introduct...New Member
TxHarleyRider2Papa ZookHarley Trike Convers...Need help bad with conversion.
PopPop13Pegasus1300New Member Introduct...New Member
Bouncer10NotgrownupHarley Tri GlideDrive Belt Replacement Time
PopPop13ol' schoolNew Member Introduct...New Member
Bowie11ol' schoolNew Member Introduct...New to trike, old time rider
Chief80138DOKKHarley Tri GlideHow many miles on your Triglide?
Bouncer10BouncerHarley Tri GlideDrive Belt Replacement Time
Bowie11trike ladyNew Member Introduct...New to trike, old time rider
Bowie11GorillaNew Member Introduct...New to trike, old time rider
Bowie11rhino 2New Member Introduct...New to trike, old time rider
Bowie11Marc HNew Member Introduct...New to trike, old time rider
SaltBushBill11Marc HNew Member Introduct...New member
Bowie11BowieNew Member Introduct...New to trike, old time rider
Rick Sinacore9RawhidekenHarley Tri GlideTour pack reinforcement
SaltBushBill11Uncle FesterNew Member Introduct...New member
Burnerboy3tommyv333Harley Trike Convers...Hey Bozo (Andrew)
Old Aviator5Old AviatorHonda TrikesGreasing a Motortrike Coupe SA rear...
Old Aviator5Old AviatorHonda TrikesGreasing a Motortrike Coupe SA rear...
Noodles1073JTJerseyHarley Freewheeler /...Tobacco Fade
Noodles1073trike ladyHarley Freewheeler /...Tobacco Fade
Old Aviator5Phu CatHonda TrikesGreasing a Motortrike Coupe SA rear...
SaltBushBill11SullyNew Member Introduct...New member
ronc44242Papa ZookHarley Tri Glidequestion
TxHarleyRider2TxHarleyRiderHarley Trike Convers...Need help bad with conversion.
Chappy KC5StrelnikovFrankensteinFrankenstein Kit
jerry1@iw.net4StrelnikovFrankensteinFrankenstein owners
TxHarleyRider2Papa ZookHarley Trike Convers...Need help bad with conversion.
Skavoola14SkavoolaNew Member Introduct...New to Trike Talk
Old Aviator5GoldWingrGregHonda TrikesGreasing a Motortrike Coupe SA rear...
El Lobo10El LoboHarley Tri GlideBeen away for a while
SaltBushBill11GorillaNew Member Introduct...New member
cissywalton2GorillaCalifornia Sidecar T...how do I change out the reverse bel...
Noodles1073Noodles107Harley Freewheeler /...Tobacco Fade
Old Aviator5Old AviatorHonda TrikesGreasing a Motortrike Coupe SA rear...
SaltBushBill11trike ladyNew Member Introduct...New member
ronc44242ronc4424Harley Tri Glidequestion
Old Aviator5SkavoolaHonda TrikesGreasing a Motortrike Coupe SA rear...
Old Aviator5rhino 2Honda TrikesGreasing a Motortrike Coupe SA rear...
Old Aviator5Old AviatorHonda TrikesGreasing a Motortrike Coupe SA rear...
cissywalton2cissywaltonCalifornia Sidecar T...how do I change out the reverse bel...
Skavoola14PosseRiderNew Member Introduct...New to Trike Talk
Skavoola14woodyNew Member Introduct...New to Trike Talk
PopPop13woodyNew Member Introduct...New Member
Speedy Pete12woodyNew Member Introduct...New member from Alberta, Canada
Vulcanology10woodyNew Member Introduct...New member
SaltBushBill11woodyNew Member Introduct...New member
SaltBushBill11hardwickbvNew Member Introduct...New member
Vulcanology10hardwickbvNew Member Introduct...New member
Speedy Pete12hardwickbvNew Member Introduct...New member from Alberta, Canada
SaltBushBill11rhino 2New Member Introduct...New member
RedOregon13NotgrownupHarley Tri GlideUpgrades on '24 Triglide?
SaltBushBill11ol' schoolNew Member Introduct...New member
Likes Likes:  7
Thanks Thanks:  0
Page 1 of 2 1 2 LastLast
Results 1 to 20 of 21

Thread: Power Vision Problem

  1. #1
    950+ Posts
    Gold Club Member

    Join Date
    Apr 2011
    Location
    Bellville, Texas, USA
    Posts
    939
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default Power Vision Problem

    I ordered a Power Vision through DK Customs Tuesday and received it yesterday (Thursday). Great service as always. I installed it this evening and Loaded the map into the ECM and the bike started up OK. I accidently hit the "Flip Screen" button and could not get the screen flipped back. Turned the bike off and restarted, screen was flipped and I could not get past the first warning screen where you had to tap "accept" and the screen was locked up at this point. Turned the bike off and let it set for awhile, unplugged the unit and plugged back in. Started bike back up and Power Vision came back on, was able to flip screen back to normal and cycle through the various settings, etc. Only problem now is the Check Engine Lamp goes off after a few seconds when you first turn the key on as it should but then it comes back on and stays on even after the engine starts.

    Anyone had this problem or have any ideas? I don't know if I can ride it or if I am shut down until I can get in touch with DK or Fuelmoto on Monday.

    Thanks,

    Sunman

  2. #2
    950+ Posts
    Gold Club Member

    Join Date
    Apr 2011
    Location
    Bellville, Texas, USA
    Posts
    939
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default

    OK, the Power Vision now seems to be working OK and I was able to flip the screen back to normal. The Check Engine Lamp is still on. Using the Power Vision I checked for DTCs and it showed code P2185 - ETC Sensor High. I tap clear and it said "Success" so I assume the code was cleared but it came back as soon as I started the engine. Same code. I looked in the manual but could not find code P2185. Does anyone know what this code is? Is there a list of DTCs somewhere I can access? I took the bike for a short ride and it ran fine but the code still shows up in the Power Vision even though I cleared it twice.

    Thanks,

    Sunman

  3. #3
    13500+ Posts FuzzyWuzHe's Avatar
    Join Date
    Dec 2014
    Location
    Grand Junction, Co. USA
    Posts
    13,245
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default

    This thread has codes ... http://www.triketalk.com/forum/threa...+trouble+codes

    But I don't know what they mean

  4. #4
    950+ Posts
    Gold Club Member

    Join Date
    Apr 2011
    Location
    Bellville, Texas, USA
    Posts
    939
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default

    Quote Originally Posted by FuzzyWuzHe View Post
    This thread has codes ... http://www.triketalk.com/forum/threa...+trouble+codesBut I don't know what they mean
    Thanks. I found this link last night and also the codes on the Fuel Moto website. On the Fuel Motto website they list "P2185 -ECT Sensor High". My Power Vision gives me "P2185 - ETC Sensor High". One says ETC and one says ECT. Don't know if this is just an error or ETC and ECT means two different things. Guess I will have to wait until Monday to talk to DK or Fuel Motto to get some help. The Check Engine Light never stayed on until I installed the Power Vision.

    Sunman

  5. #5
    900+ Posts HDB0B's Avatar
    Join Date
    Jul 2014
    Location
    S.E. PA, USA
    Posts
    925
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default

    P2185 Engine Coolant Temperature sensor High. Oil temp or coolant temp depending on system.

    You can find all the codes here > https://www.fuelmotousa.com/p-29661-...ble-codes.html

    Bob

  6. #6
    950+ Posts
    Gold Club Member

    Join Date
    Apr 2011
    Location
    Bellville, Texas, USA
    Posts
    939
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default

    Quote Originally Posted by HDB0B View Post
    P2185 Engine Coolant Temperature sensor High. Oil temp or coolant temp depending on system.You can find all the codes here > https://www.fuelmotousa.com/p-29661-...-codes.htmlBob
    Thanks Bob. I guess one of my concerns is I never had any codes show up until I installed the Power Vision. According to my shop manual ECT is Engine Coolant Temperature and ETC is Electronic Throttle Control. The Power Vision shows P-2185 ETC Sensor High indicating an Electronic Throttle Control issue. The Fuel Moto website gives the code as P-2185 ECT Sensor High indicating an Engine Coolant Temperature problem. So that is rather confusing!

    Sunman

  7. #7
    200+ Posts
    Join Date
    Apr 2017
    Location
    Murphy, Texas, USA
    Posts
    204
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default

    Have you tried reloading the stock tune to see if you still get the code?

  8. #8
    Senior Moderator
    Gold Club Member
    Gorilla's Avatar
    Join Date
    Oct 2008
    Location
    Key Largo. Fl,. USA
    Posts
    15,112
    Thanks
    0
    Thanked 2 Times in 2 Posts

    Default

    +1 on Ron's suggestion. Put it back the way it was when you started and see if the code goes away. I do not know about the new ones put in 2013 you had to cycle the ignition at least 5 times to clear the read out and light.
    Stallion #406 // 2013 Tri-Glide

  9. #9
    950+ Posts
    Gold Club Member

    Join Date
    Apr 2011
    Location
    Bellville, Texas, USA
    Posts
    939
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default

    Thanks Ron and Gorilla. I will try reloading the original and see what happens.

    Sunman

  10. #10
    18500+ Posts
    Tech Contributor
    Gold Club Member
    Jack Klarich's Avatar
    Join Date
    Oct 2016
    Location
    Jax, Fla USA
    Posts
    18,092
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default

    This code may not be historic

    This means it is not a hard code

    What happens if u ride the bike?

    I would ride it and keep track of the temperatures

    After you are sure it is not over 335 degrees rescan for codes, record them and call Fuel Moto or Kevin @ D K Customs

    The puters on these bikes are getting pretty smart, The Power Vision is a smarter tool IMO and will give you very acurate info this is my opinion from playing with mine

    I have got into the deeper workings of the Power Vision, I like how easy it is to navigate and set your bike
    Nuff Said," Were Burnin Daylight, Lets Ride"(Sober 37 years)
    Current ride : 2021 FREEWHEELER M8, oldest ride 1960 FL

  11. #11
    950+ Posts
    Gold Club Member

    Join Date
    Apr 2011
    Location
    Bellville, Texas, USA
    Posts
    939
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default

    Reloaded the stock tune Check Engine Light went off. Started bike up, light stayed off. Reloaded custom tune from Fuel Motto light came back on. Started bike up and light stayed on, code shows up again in DTC. Each time I loaded the stock tune and then reloaded the custom tune I heard a loud click (one click). Bike starts and runs fine with either tune. Think I will just ride it and watch the temp gauge and see what happens. What do you think?

    Thanks,

    Sunman

  12. #12
    950+ Posts
    Gold Club Member

    Join Date
    Apr 2011
    Location
    Bellville, Texas, USA
    Posts
    939
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default

    Quote Originally Posted by Jack Klarich View Post
    This code may not be historicThis means it is not a hard codeWhat happens if u ride the bike?I would ride it and keep track of the temperaturesAfter you are sure it is not over 335 degrees rescan for codes, record them and call Fuel Moto or Kevin @ D K CustomsThe puters on these bikes are getting pretty smart, The Power Vision is a smarter tool IMO and will give you very acurate info this is my opinion from playing with mine

    I have got into the deeper workings of the Power Vision, I like how easy it is to navigate and set your bike
    Thanks Jack. Each time I have checked the DTC the code says current. The bike starts and runs OK with either stock tune or custom tune. Only difference is the light staying on. Think I will leave the custom tune in it and ride it and see what happens. I have the gauges set up to monitor engine temp.

    Sunman

  13. #13
    18500+ Posts
    Tech Contributor
    Gold Club Member
    Jack Klarich's Avatar
    Join Date
    Oct 2016
    Location
    Jax, Fla USA
    Posts
    18,092
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default

    Quote Originally Posted by Sunman View Post
    Reloaded the stock tune Check Engine Light went off. Started bike up, light stayed off. Reloaded custom tune from Fuel Motto light came back on. Started bike up and light stayed on, code shows up again in DTC. Each time I loaded the stock tune and then reloaded the custom tune I heard a loud click (one click). Bike starts and runs fine with either tune. Think I will just ride it and watch the temp gauge and see what happens. What do you think?

    Thanks,

    The click IMO is the load of tune marrying to your ECM

    Have u had your hand on the throttle prior to this? The reason I ask is the fly by wire is VERY sensitive and will remember the last position

    Also, I dunno how many miles u have, BUT there has been an ongoing problem with the Fly By Wire throttle

    Fretting at the connections is the main problem

    Now this may be just a coincidence, but bears looking at

    TBW Issues Explained by HD Service Bulletin TT418A a MUST READ


    This is some must read info for everyone that has had issues with the TBW. This is a service bulletin issued by HD on 1/7/2011 it is bulletin # TT418A: DTC's P2135 & P2101 Theory & Diagnostics. I am going to condense this some but I also believe from my past experiences with my TBW that this also would include the P1510 code.

    TT418A service bulletin applies to 2008-Later Touring, Police & Trike Models

    Symptoms: Driveability or Performance Concerns; Abnormal or Erratic Mechanical Operation; Intermittent or Erratic Electrical Operation.

    Note: Throttle Position Sensor (TPS) circuit DTC's P0120, P0220, P0122, P0123, P0222 and P223 should take diagnostic priority over a P2135 code. If any of these TPS codes exist concurrently with the P2135, they should be investigated first using the diagnostic manual.

    The TCA has two potentiometers (designated as TPS1 & TPS2) and a electric DC motor for controlling the actuation of the throttle. The two TPS sensors work opposite of each other. As the throttle plate opens , TPS1 voltage ranges from 0.0-5.0 Volts, while TPS2 voltage ranges from 5.0-0.0 volts. The sum of the two TPS voltages should always measure approximately 5.0 volts. These wire are: TPS1, pin # 37 (BN/V wire) of the ECM, and TPS2 pin #36 (BN/R wire) of the ECM

    The TPS1 and TPS2 sensors should never add to more than 5.13 Volts Direct Current (VDC) or less than 4.87 VDC . A sum of voltages out of this range should register a current P2135 code.

    Troubleshooting:

    It is believed that FRETTING CORROSION is a major contributor of this code. A poor connection at the Throttle Control Actuator (TCA) can affect the sensor voltages reported to the ECM and this will set this DTC. As you can see from the General Information section, the sensor voltage only need to be altered by 0.13 VDC to possibly set the code.

    The most common vehicles to have these symptoms are those with more than 8,000 miles (12875 Kilometers) or 103 cubic inch and larger engines. Vibration is believed to contribute to the FRETTING CONDITION.

    Repair Procedure:

    1. While monitoring the TPS1 and TPS2 voltages on Digital Technician 2 (DT 2), wiggle the TCA [211] and the ECM [78] connectors.

    2. If the voltage changes while wiggling the ECM connector , replace the affected ECM terminals (part # 72605-08). These wires are: TPS1, pin #37 brown/violet wire of the ECM, and TPS2, pin #36 brown/red wire of the ECM.

    3. If no voltage change is noted while moving the ECM connector , the connection issue could be in the TCA. Replace all socket terminals with NEW terminals (part # 72663-11, used in current production) at the TCA connector[211B].

    4. BEFORE CONNECTING the TCA CONNECTOR, clean the male TCA pin terminals with a swab and alcohol, and ASSEMBLE WITH DIELECTRIC GREASE.

    DTC P2101

    General Information: The TCA contains two potentiometers (designated as TPS1 & TPS2) and a electric DC motor for controlling a actuation of the throttle. TPS1 & TPS2 are mounted in the TCA. They are connected to the keyed shaft of the throttle plate and used to communicate the throttle plate position.

    Each TPS supplies input to the ECM in response to the position of the throttle plate. The ECM activates the motor in the TCA to move the throttle plate, based on signals from the Twist Grip Sensor (TGS). When the ECM send voltage modulations to pins 2 & 3 0f the TCA to move the throttle motor, it checks fo subsequent TPS1 and TPS2 voltage changes. If it does not sense TPS changes it will set this code.

    Troubleshooting: First verify that the throttle plate moves freely when engine is not running. If it does not the TCA needs to be replaced.

    Poor ECM connections seem to be the most likely cause. Be aware that this issue may be aggravated by the seat pan making contact with the ECM connector. In most cases, this is caused by the installation of an aftermarket seat.

    A poor connection at ECM pins #29 & 30 could cause an interruption in voltage to the throttle motor and set this code. Similarly the ECM uses voltage from pin #52 yellow/green wire to supply power used at pins #29 & 30 and could cause the same symptoms.

    Repair Procedure:

    Identifying the connection issues at this location may be difficult.

    1. Replace all socket terminals with NEW terminals (part #72663-11 used in current production) at the TCA connector [211B].

    2. BEFORE CONNECTING the TCA CONNECTOR, clean the male TCA pin terminals with a swab and alcohol, and ASSEMBLE WITH DIELECTRIC GREASE

    This may not be the info u need but it is good to know and keep handy

    Sunman
    Have a look at the above just because
    Nuff Said," Were Burnin Daylight, Lets Ride"(Sober 37 years)
    Current ride : 2021 FREEWHEELER M8, oldest ride 1960 FL

  14. #14
    18500+ Posts
    Tech Contributor
    Gold Club Member
    Jack Klarich's Avatar
    Join Date
    Oct 2016
    Location
    Jax, Fla USA
    Posts
    18,092
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default

    Here is a diagram of the wiring from the grip to the blade @ the throttle, if u can unplug the wire connector @ the throttle actuator, clean the connections carefully, apply some { light coat} dielectric grease this could solve your problem. My 15 Freewheeler twist grip actuator went south @ 5k miles, it was covered under warranty, it did the SAME thing yours is doing now, Good Luck and hope u get it solved

    Nuff Said," Were Burnin Daylight, Lets Ride"(Sober 37 years)
    Current ride : 2021 FREEWHEELER M8, oldest ride 1960 FL

  15. #15
    950+ Posts
    Gold Club Member

    Join Date
    Apr 2011
    Location
    Bellville, Texas, USA
    Posts
    939
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default

    Thanks for the info Jack. I just got back from a run to a hamburger joint. 25 miles over and 30 miles back so only a 55 mile run. Had the custom map from Fuel Motto loaded. Had 4 gauges set up: battery voltage, engine temp, ambient air temp and fuel economy. Voltage was 14.20 to 14.30 which seems about right. Engine temp stayed around 255 to 260 when running in 5th gear at 60 mph, 3,000 rpm with the Mighty Mites on. With Mighty Mites turned off temp went up to 270 but came back down to 260 when I turned the Mighty Mites back on. At one point running 70 mph in 6th gear, 3,000 rpms temp went up to 275 deg. but came back down to 260 when I dropped back to 60 mph in 5th gear. Temps seem pretty good if they are accurate. Ambient Air temp didn't register at all. It stayed at 190 deg. which is the default high limit. It read 190 from the time I started the bike to the time I turned it off when I got back. Fuel economy is not accurate either. It read between 58 mpg and 78 mpg most of the time while running 60 mph, 3,000 rpms in 5th gear and I know that ain't right. When I gassed up and calculated the mileage it was 31.5 which is about normal. I will talk to Fuel Motto or DK on Monday and mess with it some more tomorrow. None of the codes you show above in your last post has shown up. Only the P2185 ETC Sensor High which goes away when I load the stock program back in. I will check out the connectors as per your post and see if that helps. I currently have 21,000 miles on the bike but had no problems or codes until I installed the Power Vision last night.

    Thanks,

    Sunman

  16. #16
    Sponsor
    TrikeTalk Sponsor
    DK Custom Products's Avatar
    Join Date
    Jun 2013
    Location
    Red Banks, MS
    Posts
    9,122
    Thanks
    1
    Thanked 1 Time in 1 Post

    Default

    Just saw this thread. Already responded to PM from Sunman. It looks like an error was made and a tune for a Twin-Cooled was sent instead of a tune for an air-cooled. We should have this resolved with new tune for Sunman shortly.

    While this will not damage the engine, it certainly isn't correct, nor will it be the best tune for him.

    My apologies, we'll get it fixed up shortly.

    Kevin
    www.DKCustom.com
    Call: 662-252-8828 Text: 662-420-4891
    Email: Support@DKCustomProducts.com


  17. #17
    18500+ Posts
    Tech Contributor
    Gold Club Member
    Jack Klarich's Avatar
    Join Date
    Oct 2016
    Location
    Jax, Fla USA
    Posts
    18,092
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Thumbs up

    Quote Originally Posted by DK Custom Products View Post
    Just saw this thread. Already responded to PM from Sunman. It looks like an error was made and a tune for a Twin-Cooled was sent instead of a tune for an air-cooled. We should have this resolved with new tune for Sunman shortly.

    While this will not damage the engine, it certainly isn't correct, nor will it be the best tune for him.

    My apologies, we'll get it fixed up shortly.

    Kevin
    Awesome response

    I like the way Kevin jumped in here

    I was NERVOUS when u showed your gas mileage

    I am currently stuck @ 44.7 MPG This is a REAL number, I have recalculated it at least 2 times recently and verified it via GPS and gallons I put in

    ALL I can say is THANKS to Kevin, Devin and how they hooked me up with the Power Vision and Dyno time
    Nuff Said," Were Burnin Daylight, Lets Ride"(Sober 37 years)
    Current ride : 2021 FREEWHEELER M8, oldest ride 1960 FL

  18. #18
    950+ Posts
    Gold Club Member

    Join Date
    Apr 2011
    Location
    Bellville, Texas, USA
    Posts
    939
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default

    Received a new tune and phone call from Kevin already. That is a quick response and on a Saturday too! Won't be able to download and try out the new tune until tomorrow morning but thanks Kevin for the quick response. I have always had great service from DK Custom Products.

    Sunman

  19. #19
    18500+ Posts
    Tech Contributor
    Gold Club Member
    Jack Klarich's Avatar
    Join Date
    Oct 2016
    Location
    Jax, Fla USA
    Posts
    18,092
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default

    Quote Originally Posted by Sunman View Post
    Received a new tune and phone call from Kevin already. That is a quick response and on a Saturday too! Won't be able to download and try out the new tune until tomorrow morning but thanks Kevin for the quick response. I have always had great service from DK Custom Products.

    Sunman
    Yup, Stand up guy and crew 4 sure
    Nuff Said," Were Burnin Daylight, Lets Ride"(Sober 37 years)
    Current ride : 2021 FREEWHEELER M8, oldest ride 1960 FL

  20. #20
    950+ Posts
    Gold Club Member

    Join Date
    Apr 2011
    Location
    Bellville, Texas, USA
    Posts
    939
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default Latest Up Date

    Kevin sent another new tune this morning once he got in the office and had access to all of the tunes in his library. Once I loaded it in the PV the Check Engine Light no longer stays on and there are no codes in the system. Problem solved! Took trike for a short run and everything seems to be working correctly. Now I just need to learn all of the features and capabilities of the PV.

    Thanks to Kevin for the quick response in getting the problem solved!

    Sunman

Page 1 of 2 1 2 LastLast

Similar Threads

  1. Power Vision
    By plumberdoug in forum Harley Trike Conversions
    Replies: 14
    Last Post: 05-18-2015, 03:40 PM
  2. power vision
    By plumberdoug in forum Harley Tri Glide
    Replies: 11
    Last Post: 02-01-2015, 07:28 AM
  3. Question about Power vision
    By Minnesota Dick in forum Harley Trike Conversions
    Replies: 7
    Last Post: 09-05-2012, 07:23 PM
  4. Power Vision
    By Bigbill in forum Harley Trike Conversions
    Replies: 3
    Last Post: 08-06-2012, 08:36 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •