Stallion front axle seal

[T.C.]

Damaged inner wheel bearing seals #11353

seal seems too small in circumference and when inserting the axle i hits and damages the seal and will not pass through. Anyone have info or suggestions on how to install the seals and wheel bearings. A diagram or sketch? So far two bike shops have been unable to

fix the problem. It has been out of service since

nov 2027 . It is a 2008 Stallion # 377

[tomg]

Damaged inner wheel bearing seals #11353

seal seems too small in circumference and when inserting the axle i hits and damages the seal and will not pass through. Anyone have info or suggestions on how to install the seals and wheel bearings. A diagram or sketch? So far two bike shops have been unable to

fix the problem. It has been out of service since

nov 2027 . It is a 2008 Stallion # 377

It's not the seal, it's the outer edge of the axle. It needs to be slightly beveled on the outer edge so it slides thru the seal. Grease the axle before putting it in. This works, I know! Tomg

[Gorilla]

+1 on Tom's reply. if you take the take the whole assembly apart you will what Tom is talking about. Making sure that the axle is WELL lubed and smooth. Careful alignment will get it in.

[trikervet]

To deal with the problem you have encountered, I had a dummy axle made which is exactly the length of the thickness of the wheel w/seals and bearings. I can assemble

the bearings and seals with the dummy axle in place, roll the wheel into position, then use the oem axle to push the dummy axle through.

[T.C.]

Thanks for the reply’s. Using a dummy axel sounds good but have no idea who could make me one. Not even sure if I have right parts. Can you sketch how to assemble. Is this correct sequence and parts - inner seal cr 1135 - bearing 32006- race- seal national 470025. Starts with inner seal and works out.

So far damaged two inner seals trying to mount the wheel. Have ordered replacements again .

[trikervet]

Thanks for the reply’s. Using a dummy axel sounds good but have no idea who could make me one. Not even sure if I have right parts. Can you sketch how to assemble. Is this correct sequence and parts - inner seal cr 1135 - bearing 32006- race- seal national 470025. Starts with inner seal and works out.

So far damaged two inner seals trying to mount the wheel. Have ordered replacements again .

I think you have the sequence correct.

[baldfox157]

I just went through the same issue, destroying seals. I was able to get it together by putting the axle through the inner seal first, setting the hub / rotor on the wheel, then slide the other hub onto the axle. Once together, the axle will slide side to side to get it on the bike. With the axle through the inner seal first, you don't knock the spring off or tear the seal. Just grease the crap out of the axle first.

[vongraph]

I found this list of parts for front, rebuild.

FRONT LEFT HUB ASSEMBLY PARTS TMFS-00030
No.	Description	QTY PER HUB	UNIVERSAL PART #
MTGH-0433A	E-CLIPS 5/8 BOWED	10
TMFS-00420	FRONT CALIPER BRKT SNAP RING	1
TMGH-00650	5/8 SPRING/WAVE WASHER	20
TMBR-00240	FRONT BRAKE CALIPER	1
TMBR-00270	FRONT BRAKE CALIPER BRKT LEFT	1
TMBR-00300	FRONT BRAKE ROTOR	1
TMBR-00310	FRONT CALIPER PAD RETAINER	1
TMBR-00320	FRONT BRAKE CALIPER BRKT BEAR	2	$11.50 each 6814-2RS, 70mm X 90mm X 10mm	123 bearings. 1 646-712-9672
MTBR-0182A	FLOATER PIN-BRAKE ROTOR	10
TMFS-00170	FRONT HUB (FOR INNER SEAL)	1
TMFS-00180	FRONT HUB OUTER SEAL	1	CR14939 OR NAT470625	1.5" X 2.22" X .313" measurements
TMFS-00190	FRONT HUB INNER SEAL	1	CR 11353 OR 472644 (NATIONAL OR TIMKEN)	1.125" X 2.047" X .313"
TMFS-00210	FRONT AXLE BEARING	1	HR32006XJ - NSK	$18.38 each
MTGH-0434A	FRONT BRAKE ROTOR WASHER 5/8	10
TMGH-01286	9/16 SAE FLAT WASHER Z/P	2
FRONT RIGHT HUB ASSEMBLY PARTS TMFS-00020
No.	Description	QTY PER
MTGH-0433A	E-CLIPS 5/8 BOWED	10
TMFS-00420	FRONT CALIPER BRKT SNAP RING	1
TMGH-00650	5/8 SPRING/WAVE WASHER	20
TMBR-00240	FRONT BRAKE CALIPER	1
TMBR-00290	FRONT BRAKE CALIPER BRKT RIGHT	1
TMBR-00300	FRONT BRAKE ROTOR	1
TMBR-00310	FRONT CALIPER PAD RETAINER	1
TMBR-00320	FRONT BRAKE CALIPER BRKT BEAR	2	6814-2RS
MTBR-0182A	FLOATER PIN-BRAKE ROTOR	10
TMFS-00170	FRONT HUB (FOR INNER SEAL)	1
TMFS-00180	FRONT HUB OUTER SEAL	1	CR14939 OR NAT470625
TMFS-00190	FRONT HUB INNER SEAL	1	CR11353 OR NAT472644
TMFS-00210	FRONT AXLE BEARING	1	HR32006XJ - NSK
MTGH-0434A	FRONT BRAKE ROTOR WASHER 5/8	10
TMGH-01286	9/16 SAE FLAT WASHER Z/P	2
	Rear Brake parts, Ford 500 The bearings are from France so there is $24 shipping