Tucci, I've never changed plug wires on a twin cam. On the M8, the 4 wires are tie wrapped to the frame at various locations.Originally Posted by Tucci
You have to remove the tank to do it properly.
Likes: 35
Thanks: 5
Tucci, I've never changed plug wires on a twin cam. On the M8, the 4 wires are tie wrapped to the frame at various locations.
You have to remove the tank to do it properly.
2017 Harley Davidson Freewheeler (107 cu.in. vivid black).
Wires
Jack/Michael thanks. On the 15 fw, is changing out the wires worth the hassle. I was only going to do plugs. 26,000 on odom
What is the trick on detaching the gas line. I push up on the collar and the gas line will not come loose. Do I rotate the collar until it clicks than push or what?To make changing the wires easier pulling the tank is a plus, at least on my Freewheeler it made it easier
Not a hard job to pull the tank
I had this tank off before but I be damn if I remember how removed the gas line!
HOW CAN YOU HELP THE TRIKE TALK FORUM? Become a GOLD CLUB MEMBER!
A veteran - whether active duty, retired, or reserve - is someone who, at one point in his or her life, wrote a blank check made payable to the 'United States of America', for an amount of 'up to and including my life.'
Lift up on the collar and pull down on the plastic line, they are a tight fit
Nuff Said," Were Burnin Daylight, Lets Ride"(Sober 37 years)
Current ride : 2021 FREEWHEELER M8, oldest ride 1960 FL
I put a rag behind the fuel line quick disconnect & spayed a shot of silicone on it. They can get a little crusty after sitting a few years.
2017 Harley Davidson Freewheeler (107 cu.in. vivid black).
After what I learned recently, I would. You have 26,000 miles on wires that were most likely out of spec. in the 1st. place.
2017 Harley Davidson Freewheeler (107 cu.in. vivid black).
Joe, if you buy good wires and route them good you will be money ahead
Nuff Said," Were Burnin Daylight, Lets Ride"(Sober 37 years)
Current ride : 2021 FREEWHEELER M8, oldest ride 1960 FL
Tried that. Didn't want to budge. If tried it on a friends bike and had the same problem. Has to be something I am doing wrong. Scratching my head on this one and frustrated.
HOW CAN YOU HELP THE TRIKE TALK FORUM? Become a GOLD CLUB MEMBER!
A veteran - whether active duty, retired, or reserve - is someone who, at one point in his or her life, wrote a blank check made payable to the 'United States of America', for an amount of 'up to and including my life.'
Try a shot of silicone lube, rotate the plastic line a bit while pulling down
Nuff Said," Were Burnin Daylight, Lets Ride"(Sober 37 years)
Current ride : 2021 FREEWHEELER M8, oldest ride 1960 FL
And pull straight down from the quick release. Even a bit of an angle on the pulling down will bind it up.
Kevin
www.DKCustom.com
Gear Up & Ride in! DK Custom 4th Annual Open House, June 8th. 🏍️ Click HERE For The Lowdown.
Call: 662-252-8828 Text: 662-420-4891
Email: Support@DKCustomProducts.com
Silicone
Nice tip about the silicone. I was having a tough time moving the chrome fitting. Sprayed it, rotated several times, it lifted up and the hose just about fell off!
Thanks guys. Will try that once I get back in town! Am out of town for the next week.
HOW CAN YOU HELP THE TRIKE TALK FORUM? Become a GOLD CLUB MEMBER!
A veteran - whether active duty, retired, or reserve - is someone who, at one point in his or her life, wrote a blank check made payable to the 'United States of America', for an amount of 'up to and including my life.'
Dual plug
On the 2015 Freewheeler, does the tank need to be removed or is there enough room to change front wire by loosening the front and rear mounting bolts
No removal needed on my 15 Freewheeler
The 17 M8 it is a must
Nuff Said," Were Burnin Daylight, Lets Ride"(Sober 37 years)
Current ride : 2021 FREEWHEELER M8, oldest ride 1960 FL
Tank removal
Jack, your are fountain of knowledge! Now one more question. You said you used hd plugs. Regular 6r12 or did you go with the screaming eagle 6r12g
Stick with stock plugs
The reason I say this is
1. your TC engine has Delphi Ion Sensing designed into the ECM
2. changing to a plug with a different resistance will cause the ECM to read this signal as much as being out of spec, this could cause timing issues and up to including a trouble code
3. stock plugs are cheaper and your engine was designed to run with them
I have tested and run many plugs on many HD engines, I always come back to stock
Read here
https://www.triketalk.com/forum/thre...ey-Ion-Sensing
Nuff Said," Were Burnin Daylight, Lets Ride"(Sober 37 years)
Current ride : 2021 FREEWHEELER M8, oldest ride 1960 FL
Ion
Completely mind boggling. I'm coming from the stage coach era into total computerized, concerning engines. Without someone with your experience on this site i could very well see a massive amount of money being wasted on repairs/shop hours on simple things like this(spark plugs etc)
Tucci, I stayed with the stock plugs on my M8(6R10) After 2 years, they looked very good and all 4 were identical.
With my 10% Veterans discount at my dealer, they were $19 & change for 4. I can handle that every few years.
I was gonna try NGK, but I ended up getting the wrong tip & it was a big hassle that was not worth it to save $8.
2017 Harley Davidson Freewheeler (107 cu.in. vivid black).
Ion research
The site Jack referenced was an eye opener in that ,one "small" variable in the electrical/ignition system on the newer engines can cause an untold amount of problems. And i'm sure you know, when it comes to electrical gremlins you're in limboTucci, I stayed with the stock plugs on my M8(6R10) After 2 years, they looked very good and all 4 were identical.
With my 10% Veterans discount at my dealer, they were $19 & change for 4. I can handle that every few years.
I was gonna try NGK, but I ended up getting the wrong tip & it was a big hassle that was not worth it to save $8.
Posting Permissions
