I did mine using a 15 ton press. Installation was easy . Used a bearing heater, heated the bearing to 350*, dropped all the way on the axles along with the spacers.
Ray
2017 Harley Triglide
Tijuana Border
After checking out the internet as much as I could about bearing installation, the bearing only has to be 150 degrees hotter than the shaft. From what I have been able to find the bearing should not be heated greater than 200 to 250 degrees F . Every hundred degrees you heat the bearing it expands it a thousandth of an inch. If I have something wrong here someone please set me straight.
2019 TriGlide, Twisted Cherry. Khrome Werks 2+2 bars, Eagle Lights front and rear
DK foot board extensions, rear bearing retainer plates, tourpack relocation kit and oil filter relocation kit
with cooler, powder coate tod wheels, Progressive 444 shocks,. More
I have heated them to get them off, I am NOT a big fan of heating them to install them
They are a press fit ( some call it interference fit)
They should not require heat to install if you have the right press and bearing fixtures
I have several sizes of splitters similar to this and have never had problems removing or replacing bearings
Nuff Said," Were Burnin Daylight, Lets Ride"(Sober 37 years)
Current ride : 2021 FREEWHEELER M8, oldest ride 1960 FL
Well I Guess I was taught wrong. After 28 years in the Navy and 20 years working in the civilian world working on all sizes of motors, pumps, etc I always been taught by Tech reps, Bearing reps and those with a lot more education than I had, its's OK to use a press to remove bearings , not OK to install them . Take the chance of damaging the balls, rollers. Pretty hard to get the rotating element from a 400 horsepower motor onto a hydraulic press. Most grease that are in sealed bearing will start to melt above 350 degrees.
Ray
2017 Harley Triglide
Tijuana Border
Probably as many ways to do bearings as there are pubic hairs on a redhead. Gramps taught us theres a big difference between industrial, marine,and agriculture bearings and automotive ones. There are cross applications tho. Shrink fit bearings can be heated but that dosnt always apply to automotive bearings.My goofy teenage buddys and I learned that using heat- on the wheel bearings of our Sportsters caused them to fail in under a year. I do use the freezer trick for install tho.
Nuff Said," Were Burnin Daylight, Lets Ride"(Sober 37 years)
Current ride : 2021 FREEWHEELER M8, oldest ride 1960 FL
Heat….Off ↪️ Cold On….↩️…
Sometimes a Cigar is Just a Cigar.....
2019 Tri-Glide.......
2019 TriGlide, Twisted Cherry. Khrome Werks 2+2 bars, Eagle Lights front and rear
DK foot board extensions, rear bearing retainer plates, tourpack relocation kit and oil filter relocation kit
with cooler, powder coate tod wheels, Progressive 444 shocks,. More
I have installed many many wheel bearings over the years with the exception of a trike. This my first.. I have always put the wheel bearings in the refrigerator for half an hour and a lot of times you can press them in the hole with ease. Any bearing the sits in a hole I have chilled down. Not much experience with press fit axle bearings, that's why I started this post.
2019 TriGlide, Twisted Cherry. Khrome Werks 2+2 bars, Eagle Lights front and rear
DK foot board extensions, rear bearing retainer plates, tourpack relocation kit and oil filter relocation kit
with cooler, powder coate tod wheels, Progressive 444 shocks,. More
You are heading in the right direction with the info here, press fit axle bearings are a new learning curve but nothing to be afraid of
Once I have the bearing off I like to clean the axle mating surface with emery cloth, and be sure to wipe off any residue left, clean is a must for press fit
Good luck with your project and let us know how it goes
Nuff Said," Were Burnin Daylight, Lets Ride"(Sober 37 years)
Current ride : 2021 FREEWHEELER M8, oldest ride 1960 FL
2019 TriGlide, Twisted Cherry. Khrome Werks 2+2 bars, Eagle Lights front and rear
DK foot board extensions, rear bearing retainer plates, tourpack relocation kit and oil filter relocation kit
with cooler, powder coate tod wheels, Progressive 444 shocks,. More