Recent content by Fowler
-
-
88 blazer trike
Those mask/faces are just something I 3D print for fun. I have about 60 or so of them on trees on the trails on my property. I give them to the neighbor kids also. In fact I just printed smaller versions of most of them to give out to kids that come up to me when I'm out riding my other trike.- Fowler
- Post #658
- Forum: Home Built Trikes - Non-VW
-
88 blazer trike
When I slid the rear end out I chopped up a old stool and used it to stop it from dragging I had some lumber left over from another project. I did have to but a little though So this was my idea to lock it in position. I figured I could just push some rebar through a hole and let it rest on...- Fowler
- Post #657
- Forum: Home Built Trikes - Non-VW
-
Moman H2 mic question
I just installed Moman H2 head sets on our helmets. The mic has a rounded side with 4 holes and a flat side with more smaller holes. What side goes toward the mouth- Fowler
- Thread
- Replies: 1
- Forum: General Discussion
-
88 blazer trike
Sorry, I didn't make the file smaller- Fowler
- Post #655
- Forum: Home Built Trikes - Non-VW
-
88 blazer trike
Thanks, I did get the rear out, It was easier than I thought it would be. I just jacked up the frame and slid it across the floor. There was some sawdust on the ground from another project.I think it helped- Fowler
- Post #654
- Forum: Home Built Trikes - Non-VW
-
88 blazer trike
I'M back..... I was working on striping the frame and building a Rotisserie I think tomorrow I will have the rear end out, I have to rearrange my garage/shop around to do this- Fowler
- Post #652
- Forum: Home Built Trikes - Non-VW
-
88 blazer trike
I did get a little done a couple weeks ago before my surgery. But have not gotten anything done since and it will be awhile before I can do more Pulled the engine and trany, added a temp bar on the front to sit on the rotisserie. When I am done with all the welding I will remove the bar Still...- Fowler
- Post #651
- Forum: Home Built Trikes - Non-VW
-
88 blazer trike
Never got the Right side welded up. Maybe today. I have been thinking about this wooden rotisserie I want to build The back end will be simple to connect (not easy but simple) For the front end I think I will have to make a metal adapter to fit between the trikes neck to the rotisserie I...- Fowler
- Post #649
- Forum: Home Built Trikes - Non-VW
-
88 blazer trike
A while back I though the Trike would be shorter and my angles would be out of range. So I thought I would have to use a double Cardan joint. Now that it is longer than I thought (10' wheel base, 19 1/2 drive shaft) I should NOT have to use a double cardan. My understanding is I have to keep...- Fowler
- Post #647
- Forum: Home Built Trikes - Non-VW
-
88 blazer trike
I have been adjusting my drive line angle today. I was supersized how little of a adjustment it actually took This is what I have. From what I have read this should be good. What do you all think- Fowler
- Post #645
- Forum: Home Built Trikes - Non-VW
-
88 blazer trike
It pops into each gear fine. But the way it is now it could be bumped out easy My idea is to make gate plate that will hold the shifter in each position. I have a few ideas on how to make it pop into each slot on the gate plate When I build the dash it will cover the mechanism, just the...- Fowler
- Post #643
- Forum: Home Built Trikes - Non-VW
-
88 blazer trike
I'm not sure what valves I will use yet. I still have a lot more research to do. I made the box over the master cyl yesterday. Still plenty of room to remove the master cyl and booster. Although I don't have the valves and lines to deal with yet.- Fowler
- Post #634
- Forum: Home Built Trikes - Non-VW
-
88 blazer trike
linkage at booster not depressed and depressed. I need to move the rod in the first pic to the right side of the linkage. I did not notice that until I looked at the PIC Added a support for my seat bracket. Not finished yet. I can remove the master cyl still with this brace. The problem is...- Fowler
- Post #630
- Forum: Home Built Trikes - Non-VW
-
88 blazer trike
Linkage off and on the floor. I may remake the right bracket bigger for I can use bronze bushings Brake pedal not depressed and depressed- Fowler
- Post #629
- Forum: Home Built Trikes - Non-VW
Welcome to the Trike Talk Community
Join our vibrant online community dedicated to all things Trikes! Whether you're a seasoned rider or just starting out, this is the place to share experiences, tips, and stories about your three-wheeled adventures. Explore modifications, maintenance advice, and rides, all while connecting with fellow trike enthusiasts from around the globe
Forum statistics
Trike Talk Community
Welcome to a community dedicated to the most diverse and fastest growing powersports segment, Motorcycle Trikes. Come join the discussion about the best makes and models, popular modifications and proven performance hacks, trike touring and travel, maintenance, meetups and more!
Register Already a member? LoginForum statistics
Share this page
