advice

[solwiso]

Assistance

Alright, I did the sleep mode. I follow your instruction. Then I hold it for 10 sec and reset. The red light continues to flash. When I hit it again, it continues to flash.

Next: I turn on the bike and the lights on in the rear but the left rear light the turn signal is inop. Only the right rear works. When hitting the breaks, both rear lights will not work.

The LED lights still the same. Red light is steadied. Use the phone to change the color and is not working.

I turn off the bike, then the LED light can be control with the phone.

 

[Jack Klarich]

Does your LR turn signal work? If not replace the bulb, that should clear up the trike lights, except the after market LED lights. I think they have lost the communication with the app. Can you verify they have not worked right since you changed the battery?

 

[Jack Klarich]

Alright, I did the sleep mode. I follow your instruction. Then I hold it for 10 sec and reset. The red light continues to flash. When I hit it again, it continues to flash.

Next: I turn on the bike and the lights on in the rear but the left rear light the turn signal is inop. Only the right rear works. When hitting the breaks, both rear lights will not work.

The LED lights still the same. Red light is steadied. Use the phone to change the color and is not working.

I turn off the bike, then the LED light can be control with the phone.

Has this been a problem that started when you changed the battery or is it a new today problem?

 

[Jack Klarich]

Alright, I did the sleep mode. I follow your instruction. Then I hold it for 10 sec and reset. The red light continues to flash. When I hit it again, it continues to flash.<br>

<br>

Next: I turn on the bike and the lights on in the rear but the left rear light the turn signal is inop. Only the right rear works. When hitting the breaks, both rear lights will not work. <br>

<br>

The LED lights still the same. Red light is steadied. Use the phone to change the color and is not working.<br>

<br>

I turn off the bike, then the LED light can be control with the phone.

<br>

Has this been a problem that started when you changed the battery or is it a new today problem? I have not seen a newer HD trike where the brake lights not working and not set a code, can you confirm the brake lights do not work with both the front brake lever and the rear brake lever?

 

[Jack Klarich]

Who did the install of your LED lights

According to what I have read, if they were professionally installed and documented they have a 3 year warranty, If you can access the power to these lights would un hook the power to them to rule out them as being the problem source and then start over with powering them up and syncing them

 

[solwiso]

Assistance

Yes, all started when I install the new batt.

Now, the LED works when the engine is turn off and can be control with the app as well.

But as soon I turn ignition on, the LED light turn red and cannot be control with the app or with the controller on the bike.

Now, both rear lights turn on. Is just don't work when using the foot and the hand break.

The turn signal to the right work but to the left don't work.

Maybe when I install the new batt I did a wrong connection or miss something.

 

[solwiso]

Assistance

Who did the install of your LED lights

According to what I have read, if they were professionally installed and documented they have a 3 year warranty, If you can access the power to these lights would un hook the power to them to rule out them as being the problem source and then start over with powering them up and syncing them

Yes, that's sound like a good idea..

 

[Jack Klarich]

Yes, all started when I install the new batt.

Now, the LED works when the engine is turn off and can be control with the app as well.

But as soon I turn ignition on, the LED light turn red and cannot be control with the app or with the controller on the bike.

Now, both rear lights turn on. Is just don't work when using the foot and the hand break.

The turn signal to the right work but to the left don't work.

Maybe when I install the new batt I did a wrong connection or miss something.

Probably not, it is very possible the left rear light bulb is bad or not making a clean connection in the socket, it can happen

Next time you replace the battery, or do anything electrical, pull the 50 amp main fuse, do you have an owners manual?

 

[Jack Klarich]

Yes, that's sound like a good idea..

Good place to start, I will try to stay with you and get this cleared up

Pull the LS cover off, pull the cover of the fuse box open, check your P and A fuse, if it is blown your brake lights may not light up. Keep in mind, electrical problems can be bad JUJU, especially when new lights are put on by someone other than you

 

[solwiso]

Assistance

Good afternoon

Sorry for not replying. I started to work on the bike last night and so far, I didn't finish. I forgot to tell you, had a left ankle surgery and walking around with this special ankle Brase. Anyway, was upset couldn't get this going so by accident I hit my leg with the lower fearing while walking around the bike. I stop took my medication for the pain and rest. Until the next day.

Today will continue and will keep you up to date. I do appreciate the advice you be given and the patient.

 

[rhino 2]

Yes, all started when I install the new batt.

Maybe when I install the new batt I did a wrong connection or miss something.

Electronics ;101… Go back to the last thing you Touched before the problem started you might have left a wire disconnected when You installed the battery?…

Also even with a new battery it is good Practice to fully charge the battery yourself before you install it.. even though the salesman will say the battery comes fully charged.!

 

[Jack Klarich]

Electronics ;101… Go back to the last thing you Touched before the problem started you might have left a wire disconnected when You installed the battery?…

Also even with a new battery it is good Practice to fully charge the battery yourself before you install it.. even though the salesman will say the battery comes fully charged.!

#1 on Bobs post

I would also strongly encourage you to dis connect the LED system to see how the tail light and brake lights behave

Narrow the systems down to help you isolate what the problem area is

If you have a volt meter measure your voltage before you start, a fully charged battery is a plus, make sure the connections #@ the battery are clean and tight

You should see 12.7 volts in a fully charged battery

 

[solwiso]

Assistance

Hello, good afternoon

Hope you having a good Saturday.

I'm back again here in the garage. I went out and bought Socket ASY, T-Light?DOM. Now the lights in the rear works. The turn signal works. But having problem with the break. When I break from the Handlebar, it does not work. When I press on the pedal break, will not light up. But when I release the Padel break the lights turn off and back again.

 

[solwiso]

Assistance

I did disconnect the LEDS lights. Rear lights working but still no break lights

 

[Jack Klarich]

I did disconnect the LEDS lights. Rear lights working but still no break lights

Run another scan of your ECM to see if you have any codes, if your brake lights are not working you could have a code

 

[Jack Klarich]

Hello, good afternoon

Hope you having a good Saturday.

I'm back again here in the garage. I went out and bought Socket ASY, T-Light?DOM. Now the lights in the rear works. The turn signal works. But having problem with the break. When I break from the Handlebar, it does not work. When I press on the pedal break, will not light up. But when I release the Padel break the lights turn off and back again.

This sounds backwards to me, it sounds like your brake lights are on, but when you apply the brakes they turn off?

Are the rear bulbs in correctly? Do your bulbs look like this

 

[solwiso]

Yes, the lights look the one you send

 

[solwiso]

yes the light look like the picture

 

[solwiso]

Assistance

I again check all fuze and they all are functional

 

[solwiso]

Assistance

I re did DTC and have the same codes as before.

BCM

B2123

B2124

B2151

B2271

SPDO

B1210

Now my question is,, should I deleted the codes from then last time i did DTC ?